Power Perambulator
--
--V
--V
--mJ

00:00
0
--
--
--
0

    --
    0
    0
    --
    --

    Turning footsteps into measurable electricity

    Power Perambulator explores how much of the mechanical energy in an ordinary footstep can be recovered with the piezoelectric effect. When a piezo disc is pressed and bent, it produces a short voltage pulse. Our prototype collects those pulses from nine discs, rectifies them, measures them with an Arduino and shows every step live on an LCD and on this dashboard.

    把脚步变成可以测量的电

    Power Perambulator 研究:一次普通的踩踏中,有多少机械能可以通过压电效应回收。压电片被踩压、弯曲时会产生一个短暂的电压脉冲。我们的原型把 9 片压电片的脉冲汇集起来,经过整流,由 Arduino 测量,并在 LCD 和本网页上实时显示每一步。

    Philippine Cultural College – Caloocan · TekSummit: RoboQuest 2027

    System diagram Arduino Uno TP4056 18650

    We have now added a TP4056 charging module and a single 18650 Li-ion cell to the circuit, so that harvested energy can eventually be stored in a battery.

    The TP4056 is a constant-current / constant-voltage Li-ion charger designed for a steady ~5 V input. A piezo array gives short, high-impedance pulses instead, so we have not yet measured whether footsteps put net charge into the battery. A charging LED or a momentary voltage reading is not proof. Next we will measure the current flowing into the cell over time and compare it with a resting control.

    我们现在已在电路中加入 TP4056 充电模块和一节 18650 锂电池,目标是最终把收集到的能量存进电池。

    TP4056 是恒流/恒压锂电充电芯片,设计输入是稳定的约 5V;而压电阵列输出的是短暂、高内阻的脉冲。因此,踩踏是否真的给电池充进了净电量,我们还没有测量证实。充电灯亮或瞬间电压读数都不能作为证据。下一步会测量一段时间内流入电池的电流,并与静置对照比较。

    • Piezo array produces voltage pulses when pressed (multimeter: brief 3–5 V DC readings)
    • Arduino reads the rectified signal and counts candidate steps
    • 16×2 LCD and this dashboard show voltage and steps live
    • Experiments can be recorded and exported as CSV
    • 压电阵列被按压时会产生电压脉冲(万用表直流档瞬时读数 3–5V)
    • Arduino 能读取整流后的信号并统计踩踏次数
    • 16×2 LCD 与本网页可实时显示电压和步数
    • 可以记录实验并导出 CSV

    • Measure net energy stored in the capacitor: ΔE = ½·C·(V₂² − V₁²)
    • Measure net charge into the 18650 cell over time
    • Calibrate the voltage sensor and reduce false step counts
    • Phone charging is a future goal, not a current result
    • 测量电容的净储能:ΔE = ½·C·(V₂² − V₁²)
    • 测量一段时间内流入 18650 的净电量
    • 校准电压模块,减少误计步
    • 给手机充电是未来目标,不是当前成果

    • Voltage is read by the Arduino through the voltage-sensor module (assumed 5:1 divider). It is a sampled value every ~100 ms, so very short peaks can be missed.
    • Steps are counted when the voltage reaches 1.5 V and at least 300 ms have passed since the last step.
    • Energy (E) is a firmware estimate that adds up V²/R with an assumed 1 kΩ load. It is not the energy actually stored in the capacitor or battery.
    • The Arduino and LCD are powered by USB, not by the footsteps.
    • 电压由 Arduino 通过电压模块读取(假设 5:1 分压),约每 100ms 采样一次,极短的峰值可能漏掉。
    • 步数:电压达到 1.5V,且距上一步超过 300ms,计为一步。
    • 能量 E 是固件按假设 1kΩ 负载累加 V²/R 得到的估算值,不是电容或电池里实际储存的能量。
    • Arduino 和 LCD 由 USB 供电,不是由踩踏供电。

    Reference: MDPI Micromachines 14(5):1058 — mdpi.com/2072-666x/14/5/1058